Lenticular Housing Operating Instructions

Wine Production

VLS Crossflow Machine




INTRODUCTION

The Scott lenticular filter housing is designed to be mounted upright; please make sure there is adequate overhead clearance for dome removal. A hoist or forklift is recommended for safe handling of the dome with 3 or 4 high housings. Split dome housings for easier handling are also available. Any manual lifting of the dome should be done only with proper lifting techniques and by personnel approved for maximum lifting rates exceeding the dome weight.

  • Maximum operating temperature: 284˚F (140˚C)
  • Maximum operating pressure: 159 psi (10 bar) (LIQUID PRESSURE ONLY)
  • All parts in contract with product are in 316L stainless steel
  • Standard gasket material is silicone


  • MODEL INLET/OUTLET GAUGE PORT DRAIN VENT EMPTY WEIGHT (lbs) APPROX. DOME WEIGHT (lbs)
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51


    MODEL FILTER AREA (m2) HOUSING VOLUME (dead volume without modules) (gal) VOLUME SUPRADISC II (gal) DEAD VOLUME W/SUPRADISC II (gal) EQUIVALENT TO X 40cmx40cm SHEETS EQUIVALENT TO X 60cmx60cm SHEETS TOTAL DEAD VOLUME EQUIVALENT TO FILTER PRESS 40cmx40cm (gal) % HIGHER DEAD VOLUME THAN SUPRADISC II
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51
    12" 1-High 1.50" TC 1.50" TC 1" TC 1.25" Ball Valve 115 51 51 51

    HOUSING INSTALLATION

    1. Housing inlet and outlet elbows are positioned on the bottom of the base unit with tri-clamp connections. The inlet connect is offset of the center (short elbow). Outlet connection is in the center (long elbow).
    2. Housing inlet and outlet elbows are positioned on the bottom of the base unit with tri-clamp connections. The inlet connect is offset of the center (short elbow). Outlet connection is in the center (long elbow).
    3. Housing inlet and outlet elbows are positioned on the bottom of the base unit with tri-clamp connections. The inlet connect is offset of the center (short elbow). Outlet connection is in the center (long elbow).
    4. Housing inlet and outlet elbows are positioned on the bottom of the base unit with tri-clamp connections. The inlet connect is offset of the center (short elbow). Outlet connection is in the center (long elbow).
    5. Housing inlet and outlet elbows are positioned on the bottom of the base unit with tri-clamp connections. The inlet connect is offset of the center (short elbow). Outlet connection is in the center (long elbow).
    6. Housing inlet and outlet elbows are positioned on the bottom of the base unit with tri-clamp connections. The inlet connect is offset of the center (short elbow). Outlet connection is in the center (long elbow).

    WARNING: Absolute caution should be taken with pressurized vessels. Gas or liquid pressure above the pressure vessel's rating should never be used. REgulators should always be used on gas supply if using gas.

Loading
Loading